/[pcre]/code/trunk/ChangeLog
ViewVC logotype

Diff of /code/trunk/ChangeLog

Parent Directory Parent Directory | Revision Log Revision Log | View Patch Patch

revision 85 by nigel, Sat Feb 24 21:41:13 2007 UTC revision 226 by ph10, Tue Aug 21 11:46:08 2007 UTC
# Line 1  Line 1 
1  ChangeLog for PCRE  ChangeLog for PCRE
2  ------------------  ------------------
3    
4    Version 7.3 20-Aug-07
5    ---------------------
6    
7     1. In the rejigging of the build system that eventually resulted in 7.1, the
8        line "#include <pcre.h>" was included in pcre_internal.h. The use of angle
9        brackets there is not right, since it causes compilers to look for an
10        installed pcre.h, not the version that is in the source that is being
11        compiled (which of course may be different). I have changed it back to:
12    
13          #include "pcre.h"
14    
15        I have a vague recollection that the change was concerned with compiling in
16        different directories, but in the new build system, that is taken care of
17        by the VPATH setting the Makefile.
18    
19     2. The pattern .*$ when run in not-DOTALL UTF-8 mode with newline=any failed
20        when the subject happened to end in the byte 0x85 (e.g. if the last
21        character was \x{1ec5}). *Character* 0x85 is one of the "any" newline
22        characters but of course it shouldn't be taken as a newline when it is part
23        of another character. The bug was that, for an unlimited repeat of . in
24        not-DOTALL UTF-8 mode, PCRE was advancing by bytes rather than by
25        characters when looking for a newline.
26    
27     3. A small performance improvement in the DOTALL UTF-8 mode .* case.
28    
29     4. Debugging: adjusted the names of opcodes for different kinds of parentheses
30        in debug output.
31    
32     5. Arrange to use "%I64d" instead of "%lld" and "%I64u" instead of "%llu" for
33        long printing in the pcrecpp unittest when running under MinGW.
34    
35     6. ESC_K was left out of the EBCDIC table.
36    
37     7. Change 7.0/38 introduced a new limit on the number of nested non-capturing
38        parentheses; I made it 1000, which seemed large enough. Unfortunately, the
39        limit also applies to "virtual nesting" when a pattern is recursive, and in
40        this case 1000 isn't so big. I have been able to remove this limit at the
41        expense of backing off one optimization in certain circumstances. Normally,
42        when pcre_exec() would call its internal match() function recursively and
43        immediately return the result unconditionally, it uses a "tail recursion"
44        feature to save stack. However, when a subpattern that can match an empty
45        string has an unlimited repetition quantifier, it no longer makes this
46        optimization. That gives it a stack frame in which to save the data for
47        checking that an empty string has been matched. Previously this was taken
48        from the 1000-entry workspace that had been reserved. So now there is no
49        explicit limit, but more stack is used.
50    
51     8. Applied Daniel's patches to solve problems with the import/export magic
52        syntax that is required for Windows, and which was going wrong for the
53        pcreposix and pcrecpp parts of the library. These were overlooked when this
54        problem was solved for the main library.
55    
56     9. There were some crude static tests to avoid integer overflow when computing
57        the size of patterns that contain repeated groups with explicit upper
58        limits. As the maximum quantifier is 65535, the maximum group length was
59        set at 30,000 so that the product of these two numbers did not overflow a
60        32-bit integer. However, it turns out that people want to use groups that
61        are longer than 30,000 bytes (though not repeat them that many times).
62        Change 7.0/17 (the refactoring of the way the pattern size is computed) has
63        made it possible to implement the integer overflow checks in a much more
64        dynamic way, which I have now done. The artificial limitation on group
65        length has been removed - we now have only the limit on the total length of
66        the compiled pattern, which depends on the LINK_SIZE setting.
67    
68    10. Fixed a bug in the documentation for get/copy named substring when
69        duplicate names are permitted. If none of the named substrings are set, the
70        functions return PCRE_ERROR_NOSUBSTRING (7); the doc said they returned an
71        empty string.
72    
73    11. Because Perl interprets \Q...\E at a high level, and ignores orphan \E
74        instances, patterns such as [\Q\E] or [\E] or even [^\E] cause an error,
75        because the ] is interpreted as the first data character and the
76        terminating ] is not found. PCRE has been made compatible with Perl in this
77        regard. Previously, it interpreted [\Q\E] as an empty class, and [\E] could
78        cause memory overwriting.
79    
80    10. Like Perl, PCRE automatically breaks an unlimited repeat after an empty
81        string has been matched (to stop an infinite loop). It was not recognizing
82        a conditional subpattern that could match an empty string if that
83        subpattern was within another subpattern. For example, it looped when
84        trying to match  (((?(1)X|))*)  but it was OK with  ((?(1)X|)*)  where the
85        condition was not nested. This bug has been fixed.
86    
87    12. A pattern like \X?\d or \P{L}?\d in non-UTF-8 mode could cause a backtrack
88        past the start of the subject in the presence of bytes with the top bit
89        set, for example "\x8aBCD".
90    
91    13. Added Perl 5.10 experimental backtracking controls (*FAIL), (*F), (*PRUNE),
92        (*SKIP), (*THEN), (*COMMIT), and (*ACCEPT).
93    
94    14. Optimized (?!) to (*FAIL).
95    
96    15. Updated the test for a valid UTF-8 string to conform to the later RFC 3629.
97        This restricts code points to be within the range 0 to 0x10FFFF, excluding
98        the "low surrogate" sequence 0xD800 to 0xDFFF. Previously, PCRE allowed the
99        full range 0 to 0x7FFFFFFF, as defined by RFC 2279. Internally, it still
100        does: it's just the validity check that is more restrictive.
101    
102    16. Inserted checks for integer overflows during escape sequence (backslash)
103        processing, and also fixed erroneous offset values for syntax errors during
104        backslash processing.
105    
106    17. Fixed another case of looking too far back in non-UTF-8 mode (cf 12 above)
107        for patterns like [\PPP\x8a]{1,}\x80 with the subject "A\x80".
108    
109    18. An unterminated class in a pattern like (?1)\c[ with a "forward reference"
110        caused an overrun.
111    
112    19. A pattern like (?:[\PPa*]*){8,} which had an "extended class" (one with
113        something other than just ASCII characters) inside a group that had an
114        unlimited repeat caused a loop at compile time (while checking to see
115        whether the group could match an empty string).
116    
117    20. Debugging a pattern containing \p or \P could cause a crash. For example,
118        [\P{Any}] did so. (Error in the code for printing property names.)
119    
120    21. An orphan \E inside a character class could cause a crash.
121    
122    22. A repeated capturing bracket such as (A)? could cause a wild memory
123        reference during compilation.
124    
125    23. There are several functions in pcre_compile() that scan along a compiled
126        expression for various reasons (e.g. to see if it's fixed length for look
127        behind). There were bugs in these functions when a repeated \p or \P was
128        present in the pattern. These operators have additional parameters compared
129        with \d, etc, and these were not being taken into account when moving along
130        the compiled data. Specifically:
131    
132        (a) A item such as \p{Yi}{3} in a lookbehind was not treated as fixed
133            length.
134    
135        (b) An item such as \pL+ within a repeated group could cause crashes or
136            loops.
137    
138        (c) A pattern such as \p{Yi}+(\P{Yi}+)(?1) could give an incorrect
139            "reference to non-existent subpattern" error.
140    
141        (d) A pattern like (\P{Yi}{2}\277)? could loop at compile time.
142    
143    24. A repeated \S or \W in UTF-8 mode could give wrong answers when multibyte
144        characters were involved (for example /\S{2}/8g with "A\x{a3}BC").
145    
146    25. Using pcregrep in multiline, inverted mode (-Mv) caused it to loop.
147    
148    26. Patterns such as [\P{Yi}A] which include \p or \P and just one other
149        character were causing crashes (broken optimization).
150    
151    27. Patterns such as (\P{Yi}*\277)* (group with possible zero repeat containing
152        \p or \P) caused a compile-time loop.
153    
154    28. More problems have arisen in unanchored patterns when CRLF is a valid line
155        break. For example, the unstudied pattern [\r\n]A does not match the string
156        "\r\nA" because change 7.0/46 below moves the current point on by two
157        characters after failing to match at the start. However, the pattern \nA
158        *does* match, because it doesn't start till \n, and if [\r\n]A is studied,
159        the same is true. There doesn't seem any very clean way out of this, but
160        what I have chosen to do makes the common cases work: PCRE now takes note
161        of whether there can be an explicit match for \r or \n anywhere in the
162        pattern, and if so, 7.0/46 no longer applies. As part of this change,
163        there's a new PCRE_INFO_HASCRORLF option for finding out whether a compiled
164        pattern has explicit CR or LF references.
165    
166    
167    Version 7.2 19-Jun-07
168    ---------------------
169    
170     1. If the fr_FR locale cannot be found for test 3, try the "french" locale,
171        which is apparently normally available under Windows.
172    
173     2. Re-jig the pcregrep tests with different newline settings in an attempt
174        to make them independent of the local environment's newline setting.
175    
176     3. Add code to configure.ac to remove -g from the CFLAGS default settings.
177    
178     4. Some of the "internals" tests were previously cut out when the link size
179        was not 2, because the output contained actual offsets. The recent new
180        "Z" feature of pcretest means that these can be cut out, making the tests
181        usable with all link sizes.
182    
183     5. Implemented Stan Switzer's goto replacement for longjmp() when not using
184        stack recursion. This gives a massive performance boost under BSD, but just
185        a small improvement under Linux. However, it saves one field in the frame
186        in all cases.
187    
188     6. Added more features from the forthcoming Perl 5.10:
189    
190        (a) (?-n) (where n is a string of digits) is a relative subroutine or
191            recursion call. It refers to the nth most recently opened parentheses.
192    
193        (b) (?+n) is also a relative subroutine call; it refers to the nth next
194            to be opened parentheses.
195    
196        (c) Conditions that refer to capturing parentheses can be specified
197            relatively, for example, (?(-2)... or (?(+3)...
198    
199        (d) \K resets the start of the current match so that everything before
200            is not part of it.
201    
202        (e) \k{name} is synonymous with \k<name> and \k'name' (.NET compatible).
203    
204        (f) \g{name} is another synonym - part of Perl 5.10's unification of
205            reference syntax.
206    
207        (g) (?| introduces a group in which the numbering of parentheses in each
208            alternative starts with the same number.
209    
210        (h) \h, \H, \v, and \V match horizontal and vertical whitespace.
211    
212     7. Added two new calls to pcre_fullinfo(): PCRE_INFO_OKPARTIAL and
213        PCRE_INFO_JCHANGED.
214    
215     8. A pattern such as  (.*(.)?)*  caused pcre_exec() to fail by either not
216        terminating or by crashing. Diagnosed by Viktor Griph; it was in the code
217        for detecting groups that can match an empty string.
218    
219     9. A pattern with a very large number of alternatives (more than several
220        hundred) was running out of internal workspace during the pre-compile
221        phase, where pcre_compile() figures out how much memory will be needed. A
222        bit of new cunning has reduced the workspace needed for groups with
223        alternatives. The 1000-alternative test pattern now uses 12 bytes of
224        workspace instead of running out of the 4096 that are available.
225    
226    10. Inserted some missing (unsigned int) casts to get rid of compiler warnings.
227    
228    11. Applied patch from Google to remove an optimization that didn't quite work.
229        The report of the bug said:
230    
231          pcrecpp::RE("a*").FullMatch("aaa") matches, while
232          pcrecpp::RE("a*?").FullMatch("aaa") does not, and
233          pcrecpp::RE("a*?\\z").FullMatch("aaa") does again.
234    
235    12. If \p or \P was used in non-UTF-8 mode on a character greater than 127
236        it matched the wrong number of bytes.
237    
238    
239    Version 7.1 24-Apr-07
240    ---------------------
241    
242     1. Applied Bob Rossi and Daniel G's patches to convert the build system to one
243        that is more "standard", making use of automake and other Autotools. There
244        is some re-arrangement of the files and adjustment of comments consequent
245        on this.
246    
247     2. Part of the patch fixed a problem with the pcregrep tests. The test of -r
248        for recursive directory scanning broke on some systems because the files
249        are not scanned in any specific order and on different systems the order
250        was different. A call to "sort" has been inserted into RunGrepTest for the
251        approprate test as a short-term fix. In the longer term there may be an
252        alternative.
253    
254     3. I had an email from Eric Raymond about problems translating some of PCRE's
255        man pages to HTML (despite the fact that I distribute HTML pages, some
256        people do their own conversions for various reasons). The problems
257        concerned the use of low-level troff macros .br and .in. I have therefore
258        removed all such uses from the man pages (some were redundant, some could
259        be replaced by .nf/.fi pairs). The 132html script that I use to generate
260        HTML has been updated to handle .nf/.fi and to complain if it encounters
261        .br or .in.
262    
263     4. Updated comments in configure.ac that get placed in config.h.in and also
264        arranged for config.h to be included in the distribution, with the name
265        config.h.generic, for the benefit of those who have to compile without
266        Autotools (compare pcre.h, which is now distributed as pcre.h.generic).
267    
268     5. Updated the support (such as it is) for Virtual Pascal, thanks to Stefan
269        Weber: (1) pcre_internal.h was missing some function renames; (2) updated
270        makevp.bat for the current PCRE, using the additional files
271        makevp_c.txt, makevp_l.txt, and pcregexp.pas.
272    
273     6. A Windows user reported a minor discrepancy with test 2, which turned out
274        to be caused by a trailing space on an input line that had got lost in his
275        copy. The trailing space was an accident, so I've just removed it.
276    
277     7. Add -Wl,-R... flags in pcre-config.in for *BSD* systems, as I'm told
278        that is needed.
279    
280     8. Mark ucp_table (in ucptable.h) and ucp_gentype (in pcre_ucp_searchfuncs.c)
281        as "const" (a) because they are and (b) because it helps the PHP
282        maintainers who have recently made a script to detect big data structures
283        in the php code that should be moved to the .rodata section. I remembered
284        to update Builducptable as well, so it won't revert if ucptable.h is ever
285        re-created.
286    
287     9. Added some extra #ifdef SUPPORT_UTF8 conditionals into pcretest.c,
288        pcre_printint.src, pcre_compile.c, pcre_study.c, and pcre_tables.c, in
289        order to be able to cut out the UTF-8 tables in the latter when UTF-8
290        support is not required. This saves 1.5-2K of code, which is important in
291        some applications.
292    
293        Later: more #ifdefs are needed in pcre_ord2utf8.c and pcre_valid_utf8.c
294        so as not to refer to the tables, even though these functions will never be
295        called when UTF-8 support is disabled. Otherwise there are problems with a
296        shared library.
297    
298    10. Fixed two bugs in the emulated memmove() function in pcre_internal.h:
299    
300        (a) It was defining its arguments as char * instead of void *.
301    
302        (b) It was assuming that all moves were upwards in memory; this was true
303            a long time ago when I wrote it, but is no longer the case.
304    
305        The emulated memove() is provided for those environments that have neither
306        memmove() nor bcopy(). I didn't think anyone used it these days, but that
307        is clearly not the case, as these two bugs were recently reported.
308    
309    11. The script PrepareRelease is now distributed: it calls 132html, CleanTxt,
310        and Detrail to create the HTML documentation, the .txt form of the man
311        pages, and it removes trailing spaces from listed files. It also creates
312        pcre.h.generic and config.h.generic from pcre.h and config.h. In the latter
313        case, it wraps all the #defines with #ifndefs. This script should be run
314        before "make dist".
315    
316    12. Fixed two fairly obscure bugs concerned with quantified caseless matching
317        with Unicode property support.
318    
319        (a) For a maximizing quantifier, if the two different cases of the
320            character were of different lengths in their UTF-8 codings (there are
321            some cases like this - I found 11), and the matching function had to
322            back up over a mixture of the two cases, it incorrectly assumed they
323            were both the same length.
324    
325        (b) When PCRE was configured to use the heap rather than the stack for
326            recursion during matching, it was not correctly preserving the data for
327            the other case of a UTF-8 character when checking ahead for a match
328            while processing a minimizing repeat. If the check also involved
329            matching a wide character, but failed, corruption could cause an
330            erroneous result when trying to check for a repeat of the original
331            character.
332    
333    13. Some tidying changes to the testing mechanism:
334    
335        (a) The RunTest script now detects the internal link size and whether there
336            is UTF-8 and UCP support by running ./pcretest -C instead of relying on
337            values substituted by "configure". (The RunGrepTest script already did
338            this for UTF-8.) The configure.ac script no longer substitutes the
339            relevant variables.
340    
341        (b) The debugging options /B and /D in pcretest show the compiled bytecode
342            with length and offset values. This means that the output is different
343            for different internal link sizes. Test 2 is skipped for link sizes
344            other than 2 because of this, bypassing the problem. Unfortunately,
345            there was also a test in test 3 (the locale tests) that used /B and
346            failed for link sizes other than 2. Rather than cut the whole test out,
347            I have added a new /Z option to pcretest that replaces the length and
348            offset values with spaces. This is now used to make test 3 independent
349            of link size. (Test 2 will be tidied up later.)
350    
351    14. If erroroffset was passed as NULL to pcre_compile, it provoked a
352        segmentation fault instead of returning the appropriate error message.
353    
354    15. In multiline mode when the newline sequence was set to "any", the pattern
355        ^$ would give a match between the \r and \n of a subject such as "A\r\nB".
356        This doesn't seem right; it now treats the CRLF combination as the line
357        ending, and so does not match in that case. It's only a pattern such as ^$
358        that would hit this one: something like ^ABC$ would have failed after \r
359        and then tried again after \r\n.
360    
361    16. Changed the comparison command for RunGrepTest from "diff -u" to "diff -ub"
362        in an attempt to make files that differ only in their line terminators
363        compare equal. This works on Linux.
364    
365    17. Under certain error circumstances pcregrep might try to free random memory
366        as it exited. This is now fixed, thanks to valgrind.
367    
368    19. In pcretest, if the pattern /(?m)^$/g<any> was matched against the string
369        "abc\r\n\r\n", it found an unwanted second match after the second \r. This
370        was because its rules for how to advance for /g after matching an empty
371        string at the end of a line did not allow for this case. They now check for
372        it specially.
373    
374    20. pcretest is supposed to handle patterns and data of any length, by
375        extending its buffers when necessary. It was getting this wrong when the
376        buffer for a data line had to be extended.
377    
378    21. Added PCRE_NEWLINE_ANYCRLF which is like ANY, but matches only CR, LF, or
379        CRLF as a newline sequence.
380    
381    22. Code for handling Unicode properties in pcre_dfa_exec() wasn't being cut
382        out by #ifdef SUPPORT_UCP. This did no harm, as it could never be used, but
383        I have nevertheless tidied it up.
384    
385    23. Added some casts to kill warnings from HP-UX ia64 compiler.
386    
387    24. Added a man page for pcre-config.
388    
389    
390    Version 7.0 19-Dec-06
391    ---------------------
392    
393     1. Fixed a signed/unsigned compiler warning in pcre_compile.c, shown up by
394        moving to gcc 4.1.1.
395    
396     2. The -S option for pcretest uses setrlimit(); I had omitted to #include
397        sys/time.h, which is documented as needed for this function. It doesn't
398        seem to matter on Linux, but it showed up on some releases of OS X.
399    
400     3. It seems that there are systems where bytes whose values are greater than
401        127 match isprint() in the "C" locale. The "C" locale should be the
402        default when a C program starts up. In most systems, only ASCII printing
403        characters match isprint(). This difference caused the output from pcretest
404        to vary, making some of the tests fail. I have changed pcretest so that:
405    
406        (a) When it is outputting text in the compiled version of a pattern, bytes
407            other than 32-126 are always shown as hex escapes.
408    
409        (b) When it is outputting text that is a matched part of a subject string,
410            it does the same, unless a different locale has been set for the match
411            (using the /L modifier). In this case, it uses isprint() to decide.
412    
413     4. Fixed a major bug that caused incorrect computation of the amount of memory
414        required for a compiled pattern when options that changed within the
415        pattern affected the logic of the preliminary scan that determines the
416        length. The relevant options are -x, and -i in UTF-8 mode. The result was
417        that the computed length was too small. The symptoms of this bug were
418        either the PCRE error "internal error: code overflow" from pcre_compile(),
419        or a glibc crash with a message such as "pcretest: free(): invalid next
420        size (fast)". Examples of patterns that provoked this bug (shown in
421        pcretest format) are:
422    
423          /(?-x: )/x
424          /(?x)(?-x: \s*#\s*)/
425          /((?i)[\x{c0}])/8
426          /(?i:[\x{c0}])/8
427    
428        HOWEVER: Change 17 below makes this fix obsolete as the memory computation
429        is now done differently.
430    
431     5. Applied patches from Google to: (a) add a QuoteMeta function to the C++
432        wrapper classes; (b) implement a new function in the C++ scanner that is
433        more efficient than the old way of doing things because it avoids levels of
434        recursion in the regex matching; (c) add a paragraph to the documentation
435        for the FullMatch() function.
436    
437     6. The escape sequence \n was being treated as whatever was defined as
438        "newline". Not only was this contrary to the documentation, which states
439        that \n is character 10 (hex 0A), but it also went horribly wrong when
440        "newline" was defined as CRLF. This has been fixed.
441    
442     7. In pcre_dfa_exec.c the value of an unsigned integer (the variable called c)
443        was being set to -1 for the "end of line" case (supposedly a value that no
444        character can have). Though this value is never used (the check for end of
445        line is "zero bytes in current character"), it caused compiler complaints.
446        I've changed it to 0xffffffff.
447    
448     8. In pcre_version.c, the version string was being built by a sequence of
449        C macros that, in the event of PCRE_PRERELEASE being defined as an empty
450        string (as it is for production releases) called a macro with an empty
451        argument. The C standard says the result of this is undefined. The gcc
452        compiler treats it as an empty string (which was what was wanted) but it is
453        reported that Visual C gives an error. The source has been hacked around to
454        avoid this problem.
455    
456     9. On the advice of a Windows user, included <io.h> and <fcntl.h> in Windows
457        builds of pcretest, and changed the call to _setmode() to use _O_BINARY
458        instead of 0x8000. Made all the #ifdefs test both _WIN32 and WIN32 (not all
459        of them did).
460    
461    10. Originally, pcretest opened its input and output without "b"; then I was
462        told that "b" was needed in some environments, so it was added for release
463        5.0 to both the input and output. (It makes no difference on Unix-like
464        systems.) Later I was told that it is wrong for the input on Windows. I've
465        now abstracted the modes into two macros, to make it easier to fiddle with
466        them, and removed "b" from the input mode under Windows.
467    
468    11. Added pkgconfig support for the C++ wrapper library, libpcrecpp.
469    
470    12. Added -help and --help to pcretest as an official way of being reminded
471        of the options.
472    
473    13. Removed some redundant semicolons after macro calls in pcrecpparg.h.in
474        and pcrecpp.cc because they annoy compilers at high warning levels.
475    
476    14. A bit of tidying/refactoring in pcre_exec.c in the main bumpalong loop.
477    
478    15. Fixed an occurrence of == in configure.ac that should have been = (shell
479        scripts are not C programs :-) and which was not noticed because it works
480        on Linux.
481    
482    16. pcretest is supposed to handle any length of pattern and data line (as one
483        line or as a continued sequence of lines) by extending its input buffer if
484        necessary. This feature was broken for very long pattern lines, leading to
485        a string of junk being passed to pcre_compile() if the pattern was longer
486        than about 50K.
487    
488    17. I have done a major re-factoring of the way pcre_compile() computes the
489        amount of memory needed for a compiled pattern. Previously, there was code
490        that made a preliminary scan of the pattern in order to do this. That was
491        OK when PCRE was new, but as the facilities have expanded, it has become
492        harder and harder to keep it in step with the real compile phase, and there
493        have been a number of bugs (see for example, 4 above). I have now found a
494        cunning way of running the real compile function in a "fake" mode that
495        enables it to compute how much memory it would need, while actually only
496        ever using a few hundred bytes of working memory and without too many
497        tests of the mode. This should make future maintenance and development
498        easier. A side effect of this work is that the limit of 200 on the nesting
499        depth of parentheses has been removed (though this was never a serious
500        limitation, I suspect). However, there is a downside: pcre_compile() now
501        runs more slowly than before (30% or more, depending on the pattern). I
502        hope this isn't a big issue. There is no effect on runtime performance.
503    
504    18. Fixed a minor bug in pcretest: if a pattern line was not terminated by a
505        newline (only possible for the last line of a file) and it was a
506        pattern that set a locale (followed by /Lsomething), pcretest crashed.
507    
508    19. Added additional timing features to pcretest. (1) The -tm option now times
509        matching only, not compiling. (2) Both -t and -tm can be followed, as a
510        separate command line item, by a number that specifies the number of
511        repeats to use when timing. The default is 50000; this gives better
512        precision, but takes uncomfortably long for very large patterns.
513    
514    20. Extended pcre_study() to be more clever in cases where a branch of a
515        subpattern has no definite first character. For example, (a*|b*)[cd] would
516        previously give no result from pcre_study(). Now it recognizes that the
517        first character must be a, b, c, or d.
518    
519    21. There was an incorrect error "recursive call could loop indefinitely" if
520        a subpattern (or the entire pattern) that was being tested for matching an
521        empty string contained only one non-empty item after a nested subpattern.
522        For example, the pattern (?>\x{100}*)\d(?R) provoked this error
523        incorrectly, because the \d was being skipped in the check.
524    
525    22. The pcretest program now has a new pattern option /B and a command line
526        option -b, which is equivalent to adding /B to every pattern. This causes
527        it to show the compiled bytecode, without the additional information that
528        -d shows. The effect of -d is now the same as -b with -i (and similarly, /D
529        is the same as /B/I).
530    
531    23. A new optimization is now able automatically to treat some sequences such
532        as a*b as a*+b. More specifically, if something simple (such as a character
533        or a simple class like \d) has an unlimited quantifier, and is followed by
534        something that cannot possibly match the quantified thing, the quantifier
535        is automatically "possessified".
536    
537    24. A recursive reference to a subpattern whose number was greater than 39
538        went wrong under certain circumstances in UTF-8 mode. This bug could also
539        have affected the operation of pcre_study().
540    
541    25. Realized that a little bit of performance could be had by replacing
542        (c & 0xc0) == 0xc0 with c >= 0xc0 when processing UTF-8 characters.
543    
544    26. Timing data from pcretest is now shown to 4 decimal places instead of 3.
545    
546    27. Possessive quantifiers such as a++ were previously implemented by turning
547        them into atomic groups such as ($>a+). Now they have their own opcodes,
548        which improves performance. This includes the automatically created ones
549        from 23 above.
550    
551    28. A pattern such as (?=(\w+))\1: which simulates an atomic group using a
552        lookahead was broken if it was not anchored. PCRE was mistakenly expecting
553        the first matched character to be a colon. This applied both to named and
554        numbered groups.
555    
556    29. The ucpinternal.h header file was missing its idempotency #ifdef.
557    
558    30. I was sent a "project" file called libpcre.a.dev which I understand makes
559        building PCRE on Windows easier, so I have included it in the distribution.
560    
561    31. There is now a check in pcretest against a ridiculously large number being
562        returned by pcre_exec() or pcre_dfa_exec(). If this happens in a /g or /G
563        loop, the loop is abandoned.
564    
565    32. Forward references to subpatterns in conditions such as (?(2)...) where
566        subpattern 2 is defined later cause pcre_compile() to search forwards in
567        the pattern for the relevant set of parentheses. This search went wrong
568        when there were unescaped parentheses in a character class, parentheses
569        escaped with \Q...\E, or parentheses in a #-comment in /x mode.
570    
571    33. "Subroutine" calls and backreferences were previously restricted to
572        referencing subpatterns earlier in the regex. This restriction has now
573        been removed.
574    
575    34. Added a number of extra features that are going to be in Perl 5.10. On the
576        whole, these are just syntactic alternatives for features that PCRE had
577        previously implemented using the Python syntax or my own invention. The
578        other formats are all retained for compatibility.
579    
580        (a) Named groups can now be defined as (?<name>...) or (?'name'...) as well
581            as (?P<name>...). The new forms, as well as being in Perl 5.10, are
582            also .NET compatible.
583    
584        (b) A recursion or subroutine call to a named group can now be defined as
585            (?&name) as well as (?P>name).
586    
587        (c) A backreference to a named group can now be defined as \k<name> or
588            \k'name' as well as (?P=name). The new forms, as well as being in Perl
589            5.10, are also .NET compatible.
590    
591        (d) A conditional reference to a named group can now use the syntax
592            (?(<name>) or (?('name') as well as (?(name).
593    
594        (e) A "conditional group" of the form (?(DEFINE)...) can be used to define
595            groups (named and numbered) that are never evaluated inline, but can be
596            called as "subroutines" from elsewhere. In effect, the DEFINE condition
597            is always false. There may be only one alternative in such a group.
598    
599        (f) A test for recursion can be given as (?(R1).. or (?(R&name)... as well
600            as the simple (?(R). The condition is true only if the most recent
601            recursion is that of the given number or name. It does not search out
602            through the entire recursion stack.
603    
604        (g) The escape \gN or \g{N} has been added, where N is a positive or
605            negative number, specifying an absolute or relative reference.
606    
607    35. Tidied to get rid of some further signed/unsigned compiler warnings and
608        some "unreachable code" warnings.
609    
610    36. Updated the Unicode property tables to Unicode version 5.0.0. Amongst other
611        things, this adds five new scripts.
612    
613    37. Perl ignores orphaned \E escapes completely. PCRE now does the same.
614        There were also incompatibilities regarding the handling of \Q..\E inside
615        character classes, for example with patterns like [\Qa\E-\Qz\E] where the
616        hyphen was adjacent to \Q or \E. I hope I've cleared all this up now.
617    
618    38. Like Perl, PCRE detects when an indefinitely repeated parenthesized group
619        matches an empty string, and forcibly breaks the loop. There were bugs in
620        this code in non-simple cases. For a pattern such as  ^(a()*)*  matched
621        against  aaaa  the result was just "a" rather than "aaaa", for example. Two
622        separate and independent bugs (that affected different cases) have been
623        fixed.
624    
625    39. Refactored the code to abolish the use of different opcodes for small
626        capturing bracket numbers. This is a tidy that I avoided doing when I
627        removed the limit on the number of capturing brackets for 3.5 back in 2001.
628        The new approach is not only tidier, it makes it possible to reduce the
629        memory needed to fix the previous bug (38).
630    
631    40. Implemented PCRE_NEWLINE_ANY to recognize any of the Unicode newline
632        sequences (http://unicode.org/unicode/reports/tr18/) as "newline" when
633        processing dot, circumflex, or dollar metacharacters, or #-comments in /x
634        mode.
635    
636    41. Add \R to match any Unicode newline sequence, as suggested in the Unicode
637        report.
638    
639    42. Applied patch, originally from Ari Pollak, modified by Google, to allow
640        copy construction and assignment in the C++ wrapper.
641    
642    43. Updated pcregrep to support "--newline=any". In the process, I fixed a
643        couple of bugs that could have given wrong results in the "--newline=crlf"
644        case.
645    
646    44. Added a number of casts and did some reorganization of signed/unsigned int
647        variables following suggestions from Dair Grant. Also renamed the variable
648        "this" as "item" because it is a C++ keyword.
649    
650    45. Arranged for dftables to add
651    
652          #include "pcre_internal.h"
653    
654        to pcre_chartables.c because without it, gcc 4.x may remove the array
655        definition from the final binary if PCRE is built into a static library and
656        dead code stripping is activated.
657    
658    46. For an unanchored pattern, if a match attempt fails at the start of a
659        newline sequence, and the newline setting is CRLF or ANY, and the next two
660        characters are CRLF, advance by two characters instead of one.
661    
662    
663    Version 6.7 04-Jul-06
664    ---------------------
665    
666     1. In order to handle tests when input lines are enormously long, pcretest has
667        been re-factored so that it automatically extends its buffers when
668        necessary. The code is crude, but this _is_ just a test program. The
669        default size has been increased from 32K to 50K.
670    
671     2. The code in pcre_study() was using the value of the re argument before
672        testing it for NULL. (Of course, in any sensible call of the function, it
673        won't be NULL.)
674    
675     3. The memmove() emulation function in pcre_internal.h, which is used on
676        systems that lack both memmove() and bcopy() - that is, hardly ever -
677        was missing a "static" storage class specifier.
678    
679     4. When UTF-8 mode was not set, PCRE looped when compiling certain patterns
680        containing an extended class (one that cannot be represented by a bitmap
681        because it contains high-valued characters or Unicode property items, e.g.
682        [\pZ]). Almost always one would set UTF-8 mode when processing such a
683        pattern, but PCRE should not loop if you do not (it no longer does).
684        [Detail: two cases were found: (a) a repeated subpattern containing an
685        extended class; (b) a recursive reference to a subpattern that followed a
686        previous extended class. It wasn't skipping over the extended class
687        correctly when UTF-8 mode was not set.]
688    
689     5. A negated single-character class was not being recognized as fixed-length
690        in lookbehind assertions such as (?<=[^f]), leading to an incorrect
691        compile error "lookbehind assertion is not fixed length".
692    
693     6. The RunPerlTest auxiliary script was showing an unexpected difference
694        between PCRE and Perl for UTF-8 tests. It turns out that it is hard to
695        write a Perl script that can interpret lines of an input file either as
696        byte characters or as UTF-8, which is what "perltest" was being required to
697        do for the non-UTF-8 and UTF-8 tests, respectively. Essentially what you
698        can't do is switch easily at run time between having the "use utf8;" pragma
699        or not. In the end, I fudged it by using the RunPerlTest script to insert
700        "use utf8;" explicitly for the UTF-8 tests.
701    
702     7. In multiline (/m) mode, PCRE was matching ^ after a terminating newline at
703        the end of the subject string, contrary to the documentation and to what
704        Perl does. This was true of both matching functions. Now it matches only at
705        the start of the subject and immediately after *internal* newlines.
706    
707     8. A call of pcre_fullinfo() from pcretest to get the option bits was passing
708        a pointer to an int instead of a pointer to an unsigned long int. This
709        caused problems on 64-bit systems.
710    
711     9. Applied a patch from the folks at Google to pcrecpp.cc, to fix "another
712        instance of the 'standard' template library not being so standard".
713    
714    10. There was no check on the number of named subpatterns nor the maximum
715        length of a subpattern name. The product of these values is used to compute
716        the size of the memory block for a compiled pattern. By supplying a very
717        long subpattern name and a large number of named subpatterns, the size
718        computation could be caused to overflow. This is now prevented by limiting
719        the length of names to 32 characters, and the number of named subpatterns
720        to 10,000.
721    
722    11. Subpatterns that are repeated with specific counts have to be replicated in
723        the compiled pattern. The size of memory for this was computed from the
724        length of the subpattern and the repeat count. The latter is limited to
725        65535, but there was no limit on the former, meaning that integer overflow
726        could in principle occur. The compiled length of a repeated subpattern is
727        now limited to 30,000 bytes in order to prevent this.
728    
729    12. Added the optional facility to have named substrings with the same name.
730    
731    13. Added the ability to use a named substring as a condition, using the
732        Python syntax: (?(name)yes|no). This overloads (?(R)... and names that
733        are numbers (not recommended). Forward references are permitted.
734    
735    14. Added forward references in named backreferences (if you see what I mean).
736    
737    15. In UTF-8 mode, with the PCRE_DOTALL option set, a quantified dot in the
738        pattern could run off the end of the subject. For example, the pattern
739        "(?s)(.{1,5})"8 did this with the subject "ab".
740    
741    16. If PCRE_DOTALL or PCRE_MULTILINE were set, pcre_dfa_exec() behaved as if
742        PCRE_CASELESS was set when matching characters that were quantified with ?
743        or *.
744    
745    17. A character class other than a single negated character that had a minimum
746        but no maximum quantifier - for example [ab]{6,} - was not handled
747        correctly by pce_dfa_exec(). It would match only one character.
748    
749    18. A valid (though odd) pattern that looked like a POSIX character
750        class but used an invalid character after [ (for example [[,abc,]]) caused
751        pcre_compile() to give the error "Failed: internal error: code overflow" or
752        in some cases to crash with a glibc free() error. This could even happen if
753        the pattern terminated after [[ but there just happened to be a sequence of
754        letters, a binary zero, and a closing ] in the memory that followed.
755    
756    19. Perl's treatment of octal escapes in the range \400 to \777 has changed
757        over the years. Originally (before any Unicode support), just the bottom 8
758        bits were taken. Thus, for example, \500 really meant \100. Nowadays the
759        output from "man perlunicode" includes this:
760    
761          The regular expression compiler produces polymorphic opcodes.  That
762          is, the pattern adapts to the data and automatically switches to
763          the Unicode character scheme when presented with Unicode data--or
764          instead uses a traditional byte scheme when presented with byte
765          data.
766    
767        Sadly, a wide octal escape does not cause a switch, and in a string with
768        no other multibyte characters, these octal escapes are treated as before.
769        Thus, in Perl, the pattern  /\500/ actually matches \100 but the pattern
770        /\500|\x{1ff}/ matches \500 or \777 because the whole thing is treated as a
771        Unicode string.
772    
773        I have not perpetrated such confusion in PCRE. Up till now, it took just
774        the bottom 8 bits, as in old Perl. I have now made octal escapes with
775        values greater than \377 illegal in non-UTF-8 mode. In UTF-8 mode they
776        translate to the appropriate multibyte character.
777    
778    29. Applied some refactoring to reduce the number of warnings from Microsoft
779        and Borland compilers. This has included removing the fudge introduced
780        seven years ago for the OS/2 compiler (see 2.02/2 below) because it caused
781        a warning about an unused variable.
782    
783    21. PCRE has not included VT (character 0x0b) in the set of whitespace
784        characters since release 4.0, because Perl (from release 5.004) does not.
785        [Or at least, is documented not to: some releases seem to be in conflict
786        with the documentation.] However, when a pattern was studied with
787        pcre_study() and all its branches started with \s, PCRE still included VT
788        as a possible starting character. Of course, this did no harm; it just
789        caused an unnecessary match attempt.
790    
791    22. Removed a now-redundant internal flag bit that recorded the fact that case
792        dependency changed within the pattern. This was once needed for "required
793        byte" processing, but is no longer used. This recovers a now-scarce options
794        bit. Also moved the least significant internal flag bit to the most-
795        significant bit of the word, which was not previously used (hangover from
796        the days when it was an int rather than a uint) to free up another bit for
797        the future.
798    
799    23. Added support for CRLF line endings as well as CR and LF. As well as the
800        default being selectable at build time, it can now be changed at runtime
801        via the PCRE_NEWLINE_xxx flags. There are now options for pcregrep to
802        specify that it is scanning data with non-default line endings.
803    
804    24. Changed the definition of CXXLINK to make it agree with the definition of
805        LINK in the Makefile, by replacing LDFLAGS to CXXFLAGS.
806    
807    25. Applied Ian Taylor's patches to avoid using another stack frame for tail
808        recursions. This makes a big different to stack usage for some patterns.
809    
810    26. If a subpattern containing a named recursion or subroutine reference such
811        as (?P>B) was quantified, for example (xxx(?P>B)){3}, the calculation of
812        the space required for the compiled pattern went wrong and gave too small a
813        value. Depending on the environment, this could lead to "Failed: internal
814        error: code overflow at offset 49" or "glibc detected double free or
815        corruption" errors.
816    
817    27. Applied patches from Google (a) to support the new newline modes and (b) to
818        advance over multibyte UTF-8 characters in GlobalReplace.
819    
820    28. Change free() to pcre_free() in pcredemo.c. Apparently this makes a
821        difference for some implementation of PCRE in some Windows version.
822    
823    29. Added some extra testing facilities to pcretest:
824    
825        \q<number>   in a data line sets the "match limit" value
826        \Q<number>   in a data line sets the "match recursion limt" value
827        -S <number>  sets the stack size, where <number> is in megabytes
828    
829        The -S option isn't available for Windows.
830    
831    
832    Version 6.6 06-Feb-06
833    ---------------------
834    
835     1. Change 16(a) for 6.5 broke things, because PCRE_DATA_SCOPE was not defined
836        in pcreposix.h. I have copied the definition from pcre.h.
837    
838     2. Change 25 for 6.5 broke compilation in a build directory out-of-tree
839        because pcre.h is no longer a built file.
840    
841     3. Added Jeff Friedl's additional debugging patches to pcregrep. These are
842        not normally included in the compiled code.
843    
844    
845    Version 6.5 01-Feb-06
846    ---------------------
847    
848     1. When using the partial match feature with pcre_dfa_exec(), it was not
849        anchoring the second and subsequent partial matches at the new starting
850        point. This could lead to incorrect results. For example, with the pattern
851        /1234/, partially matching against "123" and then "a4" gave a match.
852    
853     2. Changes to pcregrep:
854    
855        (a) All non-match returns from pcre_exec() were being treated as failures
856            to match the line. Now, unless the error is PCRE_ERROR_NOMATCH, an
857            error message is output. Some extra information is given for the
858            PCRE_ERROR_MATCHLIMIT and PCRE_ERROR_RECURSIONLIMIT errors, which are
859            probably the only errors that are likely to be caused by users (by
860            specifying a regex that has nested indefinite repeats, for instance).
861            If there are more than 20 of these errors, pcregrep is abandoned.
862    
863        (b) A binary zero was treated as data while matching, but terminated the
864            output line if it was written out. This has been fixed: binary zeroes
865            are now no different to any other data bytes.
866    
867        (c) Whichever of the LC_ALL or LC_CTYPE environment variables is set is
868            used to set a locale for matching. The --locale=xxxx long option has
869            been added (no short equivalent) to specify a locale explicitly on the
870            pcregrep command, overriding the environment variables.
871    
872        (d) When -B was used with -n, some line numbers in the output were one less
873            than they should have been.
874    
875        (e) Added the -o (--only-matching) option.
876    
877        (f) If -A or -C was used with -c (count only), some lines of context were
878            accidentally printed for the final match.
879    
880        (g) Added the -H (--with-filename) option.
881    
882        (h) The combination of options -rh failed to suppress file names for files
883            that were found from directory arguments.
884    
885        (i) Added the -D (--devices) and -d (--directories) options.
886    
887        (j) Added the -F (--fixed-strings) option.
888    
889        (k) Allow "-" to be used as a file name for -f as well as for a data file.
890    
891        (l) Added the --colo(u)r option.
892    
893        (m) Added Jeffrey Friedl's -S testing option, but within #ifdefs so that it
894            is not present by default.
895    
896     3. A nasty bug was discovered in the handling of recursive patterns, that is,
897        items such as (?R) or (?1), when the recursion could match a number of
898        alternatives. If it matched one of the alternatives, but subsequently,
899        outside the recursion, there was a failure, the code tried to back up into
900        the recursion. However, because of the way PCRE is implemented, this is not
901        possible, and the result was an incorrect result from the match.
902    
903        In order to prevent this happening, the specification of recursion has
904        been changed so that all such subpatterns are automatically treated as
905        atomic groups. Thus, for example, (?R) is treated as if it were (?>(?R)).
906    
907     4. I had overlooked the fact that, in some locales, there are characters for
908        which isalpha() is true but neither isupper() nor islower() are true. In
909        the fr_FR locale, for instance, the \xAA and \xBA characters (ordmasculine
910        and ordfeminine) are like this. This affected the treatment of \w and \W
911        when they appeared in character classes, but not when they appeared outside
912        a character class. The bit map for "word" characters is now created
913        separately from the results of isalnum() instead of just taking it from the
914        upper, lower, and digit maps. (Plus the underscore character, of course.)
915    
916     5. The above bug also affected the handling of POSIX character classes such as
917        [[:alpha:]] and [[:alnum:]]. These do not have their own bit maps in PCRE's
918        permanent tables. Instead, the bit maps for such a class were previously
919        created as the appropriate unions of the upper, lower, and digit bitmaps.
920        Now they are created by subtraction from the [[:word:]] class, which has
921        its own bitmap.
922    
923     6. The [[:blank:]] character class matches horizontal, but not vertical space.
924        It is created by subtracting the vertical space characters (\x09, \x0a,
925        \x0b, \x0c) from the [[:space:]] bitmap. Previously, however, the
926        subtraction was done in the overall bitmap for a character class, meaning
927        that a class such as [\x0c[:blank:]] was incorrect because \x0c would not
928        be recognized. This bug has been fixed.
929    
930     7. Patches from the folks at Google:
931    
932          (a) pcrecpp.cc: "to handle a corner case that may or may not happen in
933          real life, but is still worth protecting against".
934    
935          (b) pcrecpp.cc: "corrects a bug when negative radixes are used with
936          regular expressions".
937    
938          (c) pcre_scanner.cc: avoid use of std::count() because not all systems
939          have it.
940    
941          (d) Split off pcrecpparg.h from pcrecpp.h and had the former built by
942          "configure" and the latter not, in order to fix a problem somebody had
943          with compiling the Arg class on HP-UX.
944    
945          (e) Improve the error-handling of the C++ wrapper a little bit.
946    
947          (f) New tests for checking recursion limiting.
948    
949     8. The pcre_memmove() function, which is used only if the environment does not
950        have a standard memmove() function (and is therefore rarely compiled),
951        contained two bugs: (a) use of int instead of size_t, and (b) it was not
952        returning a result (though PCRE never actually uses the result).
953    
954     9. In the POSIX regexec() interface, if nmatch is specified as a ridiculously
955        large number - greater than INT_MAX/(3*sizeof(int)) - REG_ESPACE is
956        returned instead of calling malloc() with an overflowing number that would
957        most likely cause subsequent chaos.
958    
959    10. The debugging option of pcretest was not showing the NO_AUTO_CAPTURE flag.
960    
961    11. The POSIX flag REG_NOSUB is now supported. When a pattern that was compiled
962        with this option is matched, the nmatch and pmatch options of regexec() are
963        ignored.
964    
965    12. Added REG_UTF8 to the POSIX interface. This is not defined by POSIX, but is
966        provided in case anyone wants to the the POSIX interface with UTF-8
967        strings.
968    
969    13. Added CXXLDFLAGS to the Makefile parameters to provide settings only on the
970        C++ linking (needed for some HP-UX environments).
971    
972    14. Avoid compiler warnings in get_ucpname() when compiled without UCP support
973        (unused parameter) and in the pcre_printint() function (omitted "default"
974        switch label when the default is to do nothing).
975    
976    15. Added some code to make it possible, when PCRE is compiled as a C++
977        library, to replace subject pointers for pcre_exec() with a smart pointer
978        class, thus making it possible to process discontinuous strings.
979    
980    16. The two macros PCRE_EXPORT and PCRE_DATA_SCOPE are confusing, and perform
981        much the same function. They were added by different people who were trying
982        to make PCRE easy to compile on non-Unix systems. It has been suggested
983        that PCRE_EXPORT be abolished now that there is more automatic apparatus
984        for compiling on Windows systems. I have therefore replaced it with
985        PCRE_DATA_SCOPE. This is set automatically for Windows; if not set it
986        defaults to "extern" for C or "extern C" for C++, which works fine on
987        Unix-like systems. It is now possible to override the value of PCRE_DATA_
988        SCOPE with something explicit in config.h. In addition:
989    
990        (a) pcreposix.h still had just "extern" instead of either of these macros;
991            I have replaced it with PCRE_DATA_SCOPE.
992    
993        (b) Functions such as _pcre_xclass(), which are internal to the library,
994            but external in the C sense, all had PCRE_EXPORT in their definitions.
995            This is apparently wrong for the Windows case, so I have removed it.
996            (It makes no difference on Unix-like systems.)
997    
998    17. Added a new limit, MATCH_LIMIT_RECURSION, which limits the depth of nesting
999        of recursive calls to match(). This is different to MATCH_LIMIT because
1000        that limits the total number of calls to match(), not all of which increase
1001        the depth of recursion. Limiting the recursion depth limits the amount of
1002        stack (or heap if NO_RECURSE is set) that is used. The default can be set
1003        when PCRE is compiled, and changed at run time. A patch from Google adds
1004        this functionality to the C++ interface.
1005    
1006    18. Changes to the handling of Unicode character properties:
1007    
1008        (a) Updated the table to Unicode 4.1.0.
1009    
1010        (b) Recognize characters that are not in the table as "Cn" (undefined).
1011    
1012        (c) I revised the way the table is implemented to a much improved format
1013            which includes recognition of ranges. It now supports the ranges that
1014            are defined in UnicodeData.txt, and it also amalgamates other
1015            characters into ranges. This has reduced the number of entries in the
1016            table from around 16,000 to around 3,000, thus reducing its size
1017            considerably. I realized I did not need to use a tree structure after
1018            all - a binary chop search is just as efficient. Having reduced the
1019            number of entries, I extended their size from 6 bytes to 8 bytes to
1020            allow for more data.
1021    
1022        (d) Added support for Unicode script names via properties such as \p{Han}.
1023    
1024    19. In UTF-8 mode, a backslash followed by a non-Ascii character was not
1025        matching that character.
1026    
1027    20. When matching a repeated Unicode property with a minimum greater than zero,
1028        (for example \pL{2,}), PCRE could look past the end of the subject if it
1029        reached it while seeking the minimum number of characters. This could
1030        happen only if some of the characters were more than one byte long, because
1031        there is a check for at least the minimum number of bytes.
1032    
1033    21. Refactored the implementation of \p and \P so as to be more general, to
1034        allow for more different types of property in future. This has changed the
1035        compiled form incompatibly. Anybody with saved compiled patterns that use
1036        \p or \P will have to recompile them.
1037    
1038    22. Added "Any" and "L&" to the supported property types.
1039    
1040    23. Recognize \x{...} as a code point specifier, even when not in UTF-8 mode,
1041        but give a compile time error if the value is greater than 0xff.
1042    
1043    24. The man pages for pcrepartial, pcreprecompile, and pcre_compile2 were
1044        accidentally not being installed or uninstalled.
1045    
1046    25. The pcre.h file was built from pcre.h.in, but the only changes that were
1047        made were to insert the current release number. This seemed silly, because
1048        it made things harder for people building PCRE on systems that don't run
1049        "configure". I have turned pcre.h into a distributed file, no longer built
1050        by "configure", with the version identification directly included. There is
1051        no longer a pcre.h.in file.
1052    
1053        However, this change necessitated a change to the pcre-config script as
1054        well. It is built from pcre-config.in, and one of the substitutions was the
1055        release number. I have updated configure.ac so that ./configure now finds
1056        the release number by grepping pcre.h.
1057    
1058    26. Added the ability to run the tests under valgrind.
1059    
1060    
1061  Version 6.4 05-Sep-05  Version 6.4 05-Sep-05
1062  ---------------------  ---------------------
1063    

Legend:
Removed from v.85  
changed lines
  Added in v.226

webmaster@exim.org
ViewVC Help
Powered by ViewVC 1.1.12